Main Article Count: 2
More Power Tuning Overview Article Count: 63
All Electronic Engine Tuning comes in 3 types
1. Complete ECU replacement
These are becoming available but software resolution is no match for factory OEM ECU. These are more biased to installing CRD engines in older vehicles. Installation is extremely time-consuming, so labour costs become very expensive.
2. ECU Re-program
This was mainly for European vehicles, and until around 2004 this was the best option. But for later vehicles the ECU is fitted with a Data counter, which tells the dealer it has been reprogrammed and Dealers can now overwrite the re-program during vehicle services. So the performance map needs to be re-installed after every service. The only way to bypass this Data counter is to open the ECU case and program direct to the circuit board.
The MorePower Pocket Flash Programmer was a partial solution to this, allowing the customer to self-install either the standard or performance map. But it needs too many modifications to work on every car. Another problem with ECU reprogramming is that in many cases the performance map being installed in the car is Security-Coded; so even the installer does not have access to the contents, and cannot adjust it.
This method of Tuning has been made obsolete by our Multi-Function TB-CRD2-4 range of Tuning Boxes (information further down the page). Which is able to connect & control the same functions as an ECU Reprogram on both Petrol & Diesel engines.
We can do either ECU Reprogram or Tuning Box. The Tuning Box is our preferred method as it can be switched on or off, or removed to put vehicle back to standard at any time. It is also better for creating a custom program because the Data Log stores the individual vehicles running parameters. So if the customer fits something like a sports exhaust, then drives the car for a normal week, we can then read what changed in that week compared to what was in the data before.
Where an ECU Reprogram is carried out in an artificial environment - on a dyno at High RPM/Full throttle/Full Load - How often will the vehicle be driven like this?
3. Tuning Box / Interceptor Box / Chip
The Tuning Box is the most flexible of the three and readily available in different levels of sophistication. Plus in some cases the Tuning Box you have purchased may be able to be reprogrammed & new wiring loom for your next vehicle. If you sell a vehicle with an ECU reprogram or aftermarket ECU the money spent will be lost. There is an Industry Propagated Fuel Pressure Myth (see extended explanation below) & most surprisingly, the members of the industry who most use this as a selling tool are actually selling Tuning systems which are only supplying more fuel. This is by either making the Injectors open for longer (Duty Cycle) or via the Pressure Sensor & both get the same power gain from the same 10% increase in fuel delivered to combustion. We sell both Injector Duty Cycle & Fuel Rail Sensor Tuning boxes styles as both styles “do work if programmed correctly”, but some engines work better & safer with one style instead of the other, so instead of compromising the Tuning on some vehicles, using the wrong method we sell both.
The question which customers fail to ask is what effect does only adding more fuel do to the engines Air/Fuel ratio? It is obvious that you can’t keep adding Fuel & also claim that the Air/Fuel ratio are not affected. It is only possible to add fuel to the point where the Air/Fuel ratio still allows it to burn the fuel.
Our solution is to also control Turbo Boost; by connecting to the MAP (Boost) Sensor. Through this sensor we can increase airflow into the engine as well. This allows our Tuning Box to match the Air/Fuel ratio, or in situations where the engine, even in standard tune, runs too rich, we add Boost instead of Fuel. This function can also be very useful in situations like Diesel/Gas where an extra fuel has been added, which can cause potentially dangerous Air/Fuel ratio problems.
Tuning Boxes for Semi-Mechanical Diesel Pumps
TB-MP & TB-DENSO covers most of the early Diesels, which have some Electronic control of the pump, but still use mechanical pressure operated injectors, including vehicles like Early Mitsubishi Pajero 3.2L, Toyota Hilux & Prado 1KZ, Landcruiser 1HD, Rodeo, Patrol & Navara 2.8-3.0L motors. Most companies use the same Tuning Box to fit all of these, which are connected via separate wires, and take about an hour to fit. In our range we have TB-MP which is adjusted using a potentiometer type screw.
TB-DENSO is a Jumper (like a fuse) Adjust Boxes. This box can also fit VP44 type injection systems, but at Morepower we now only use this type of box on the Toyota 1KZ & 1HD engines.
Buy a Morepower Tuning Box for my vehicle.
TB-VP44 fits Audi Allroad, Ford Transit, Holden Rodeo, Nissan Patrol & Navara 3.0L, which all use the Bosch VP44 injection pump. Because companies like BMW and Audi also used this pump, there was need of a market leading, high technology product to maximise the potential of the VP44 pump. So we have the Morepower TB-VP44 a Plug-in, 3D, PC Adjust box, which gives us the ability to tune these vehicles in the same 3D way we tune a Common Rail engine, and can be installed in minutes. There is no need to attach any extra wires using unreliable scotch blocks, this system plugs in with OEM Waterproof plugs.
Tuning Systems for Common Rail Diesels come in 3 styles
But Only One Style Can Tune Both Petrol & Diesel
Injector Control –
TB-PD1 & 2 is designed to fit VAG (VW/Audi) PD engines. These use a system which is the reverse of the older systems, but is now going out of production. They use Electronically Controlled Injectors (Unit Injection), with the fuel pressure being mechanically created. The style of Tuning Box used for this type of injection, plugs to the injector (downstream of the ECU), and controls the amount of time the injector will remain open. Early vehicles use our TB-PD1, which is adjusted using a potentiometer type screw. Our TB-PD2 system is full 3D PC controlled using the same software as our TB-VP44 & TB-CRPD boxes.
Buy a Morepower Tuning Box for my vehicle.
TB-CRPD Injector (Duty Cycle) Control is a hybrid of the Morepower VAG Unit Injection TB-PD2 box, which is used to control the injectors on full Common Rail engines. There are a few brands of Tuning Boxes, which can do this, but most work on the same parallel-line, Screwdriver or Jumper adjustment method. Our MorePower TB-CRPD box is the only one available with full PC-only, 3D mapping, allowing us to independently increase or decrease fuelling at any RPM or Load point in the map.
It is basic mathematics that to get a Diesel engine to produce more power, it will need more fuel to deliver the power. If a dyno graph shows a big power gain at high engine rpm, it can only be achieved by increased fuel delivered to combustion by more than was there before. Both Injector Control & Fuel Rail Sensor Tuning boxes do the cause the High Pressure Pump to run up to 10% higher than standard, But only if the Tuning continues into the high rpm areas of the fuel map. We sell both Injector Duty Cycle & Fuel Rail Sensor Tuning boxes styles as both styles “do work if programmed correctly”, but some engines work better & safer with one style instead of the other. On some engines the weak point is the Injectors, on others it is the Fuel Rail Sensors. So instead of compromising the Tuning on some vehicles, using the wrong method we sell both.
Some brands of Injector Control Tuning boxes need to have a wire connected to the accel pedal sensor so that they know when you want to have more power, but this then causes problems with Cruise Control Systems which are not linked to the accel pedal sensor.
Our MorePower Injector Control box does not need any extra wires. Our box works out the Engine RPM by counting all the Injector Pulses. Then our box measures how long each pulse lasts, the harder the driver presses down on the accel pedal then the Injector Pulses are longer duration. This then also works exactly the same with the Cruise Control. 
Fuel Rail Sensor Control –
This covers all boxes, which connect to the Fuel Rail Sensor. This sensor only transmits data related to Fuel Pressure (Ref: Robert Bosch) this is a variable 0-5volt signal. The Tuning Box adjusts this pressure signal by up to 10%, prior to (up-stream) the signal reaching the ECU. It is basic mathematics that to get a Diesel engine to produce more power, it will need more fuel to deliver the power. If a dyno graph shows a big power gain at high engine rpm, it can only be achieved by increased fuel delivered to combustion by more than was there before. Both Injector Control & Fuel Rail Sensor Tuning boxes do the cause the High Pressure Pump to run up to 10% higher than standard, But only if the Tuning continues into the high rpm areas of the fuel map. We sell both Injector Duty Cycle & Fuel Rail Sensor Tuning boxes styles as both styles “do work if programmed correctly”, but some engines work better & safer with one style instead of the other. On some engines the weak point is the Injectors, on others it is the Fuel Rail Sensors. So instead of compromising the Tuning on some vehicles, using the wrong method, we sell both.
Most of cheaper versions of these systems are only screwdriver or jumper adjusted, and consists of a parallel-line adjustment, usually up to half a volt below the real signal. If this causes problems, a Screwdriver box then needs to be de-tuned or if possible a PC tune, which adjusts the switch on, and switch off points on the parallel-line adjustment, or moves this line either up or down further. But if the problem is too little fuel at one rpm point and too much fuel at another rpm point, this cannot be fixed with this type Screwdriver type of box.
Our Morepower TB-CRD box can fix this problem, it has a full 3D mapping curve, allowing us to independently increase or decrease fuelling at any point in the map. An example of this is the late model Navara D40 2.5L Auto, which runs too rich from the factory. When we tune this vehicle in standard form we give it a slight increase in fuel just above idle, to help the vehicle get moving. Then reduce fuel in mid range to give better cruise economy. Then again increase fuel at top end for full throttle acceleration. This gives good power and drivability and improves economy.
Buy a Morepower Tuning Box for my vehicle.
Multi-Function Tuning Box for Petrol & Diesel
Our new MorePower TB-CRD2, 3 & 4 Tuning Boxes contain multiple Map Chips, and have the ability to control different engine functions at the same time. The wiring looms come in a variety of designs, with the ability to plug into and control different engine functions, the same functions as an ECU re-program on both Petrol & Diesel engines. The box can be removed and re-installed at any time eg: services.
Just as Diesel engines have adopted previous EFI Petrol technology, now Direct Injection Petrol engines are borrowing the technology of Common Rail Diesels. Most new Petrol’s will be smaller capacity Turbo engines, this will allow a huge potential for Tuning.
In 2005, we introduced the first version of the MorePower TB-CRD2 Diesel Tuning Box, which was mapped to run different engine functions like Fuel & Boost Control; with 128 adjustment points per map (current Screwdriver boxes still only have a maximum of 10 points). After testing this early system on Direct Injection Petrol's, we realised that the Petrol mapping required a much finer tuning resolution, so a new style of MorePower Box was created in 2008 with 1024 adjustment points per map as in table below.
In 2012 this was further developed to have a fully virtual map system with no fixed grid table boundary. This now has an unlimited resolution & is used for both Petrol & Diesel programs, controlling functions like Cam Angle Sensor, Temperature Sensor, Fuel Rail Sensor & MAP (Boost) Sensor. Some engines now have multiple Fuel Rail or MAP Sensors, which for other companies requires fitting multiple Tuning Boxes. The extra complication with fitting multiple boxes is there is no communication between these boxes. In our system not only does require just one box, but we also choose how all these different Sensors Data is both cross referenced & modified in a similar way to how the OEM ECU functions. With these boxes we have also added external Potentiometer Adjusters (10 levels on each adjuster) for making small compensations for changes dealers have made during OEM ECU updates. Depending on the vehicle type these boxes come is 3 types. First has a single adjuster for global (all systems) settings. The second has twin adjusters, with separate one for peak Fuel & Boost. The third type has three adjusters for separate Fuel, Boost & Map Timing.
Input & Output options include Cam angle, Inj pressure, MAP, MAF, TPS, Temp. This new system is available for most European vehicles, plus we have also released the Nissan 2.5L, Holden/Isuzu 3.0L CRD & Jeep VM 3.0L CRD which now have Fuel, Boost and Cam Timing sensor connections. The new box functions also include:
In-built Temperature sensor which reduces tuning on cold engine (vehicle needs to warm prior to Dyno Tuning).
DPF Particulate filter regeneration detect, which reduces tuning during this cycle.
Data-Log system which in real time, stores all information the box receives from the cars sensors.
Plus - how often the box did get power even if engine was not started, eg: Ignition On. How often the engine started with box plugged in. How long the engine ran with box each time. The date of the first programming of this box. How many times the box has been reprogrammed. The date of the last programming of this box.
Buy a Morepower Tuning Box for my vehicle.
What makes our system different?
The biggest problem with most Tuning Systems is that they use the same generic box and program on many different cars. But this is then a compromise on all of these cars. For example, even though a Hilux has the same engine as the Prado, the Prado has an intercooler, so it has different air temperatures; this requires a different fuel map. The Screwdriver Tuning systems claim to be directly transferable between totally different vehicles (no additional programming required). And yet also claim to be individually tuned to suit different vehicles. Screwdriver adjusted boxes do not properly compensate for modifications like exhaust, as we find that only certain parts of the map need adjusting, not the whole map moved up or down, so deciding which direction to turn the screw will always result in a compromise.
Many companies sell tuning systems, but only plug to one sensor or just to the injectors, so in both cases only control fuel. Some companies are starting to see the need to add boost as well to balance air/fuel ratio, but still only run 2d maps. The Morepower Tuning box is the only Tuning system which plugs to multiple sensors, controlling multiple functions with full 3d resolution. It is the most sophisticated system developed for these engines.
You must also note that all power gains listed were achieved on standard vehicles, with no other modifications. So the systems are also a “stand alone” modification, which when combined with other products, achieve further gains. If you plan to install a performance exhaust, the program we install in the box will be different to our standard program. Screwdriver adjusted boxes do not compensate for modifications like exhaust, as we find that only certain parts of the map need adjusting, not the whole map moved up or down.
Tuning engines is not a simple case of “one size fits all”, there are many factors which determine what is needed to tune “your” vehicle. We have 3 basic styles of programs, we then make further modifications to these programs styles to match your vehicle configuration:
Eco programs are biased towards Fuel Savings. The Fuel curve is designed to improve torque from less use of the accel pedal, this encourages the driver to not use Acceleration Enrich Mode. The Box can be set to switch off completely at full throttle, so it is not possible for the vehicle use more fuel than standard. This style of program is popular with Courier and Trucking companies, where the vehicle has been chosen well to do it’s job, but they would like to reduce the running costs, especially when the owner is not the driver.
Towing programs are designed to increase torque, and to sustain the torque curve as high up the rpm range as required. But the focus of this style of program is vehicles traveling long distances at the same road speed, but under load. Having the correct fuel at this speed, encourages the driver to not need to use Acceleration Enrich Mode, and can save fuel if driven correctly. Full throttle fuel can be increased as well, or switched off like in an Eco program. 75% of our programs are based on this style.
Rally programs are designed for light weight performance vehicles. An engine with this style of program is constantly using most of its rev range. These programs are not suited to loaded vehicles travelling at constant highway speeds. But this style of program is still popular for city drivers with the new generation, performance Diesel cars.
Only a person, who is qualified, is permitted to tune our late model Morepower Tuning boxes with a PC. This is why our shops will not supply a Tuning Box off the shelf. All of our shops order boxes as required, and tuned to match your vehicle modifications. We have created different maps to match modifications like larger exhausts, larger tyres, LPG systems etc.. All of the Morepower PC adjusted Boxes also contain a Data Log function. So if the customer makes changes to the vehicle, they can run the vehicle for about a week after the modification, and then post the Tuning Box back. Our Morepower technician can read the change to the vehicle from the Data Log, and from this information, can make program adjustments, this process can cost $50 - $100, depending on time required. Some vehicles are being used to carry enormous loads; we have seen 118kw Nissans carrying over 5tons. Once you calculate the combined weight of a fully stocked large caravan, the roof rack load plus what is inside the vehicle even the accessories fitted to the vehicle like bulbar & winch. Then we have to also calculate for additional load caused by the gear ratio changes caused by oversized tyres. It is fairly obvious the program to tune a vehicle in this situation has to be very well balanced & matched to these vehicles requirements.
Buy a Morepower Tuning Box for my vehicle.
Find out more:
Hiclone Fuelsaver Article Count: 4
Hiclone is a simple non-moving and maintenance-free device made of stainless steel, which fits inside the air filter housing of a carburetor or in the air induction hose on EFI, turbo, LPG or diesel engines. Which creates a swirling cyclone or tornado like effect to the airflow into the intake manifold and combustion chamber of any engine.
Hiclone has No moving parts and will therefore out last the life expectancy of any engine.
Hiclone requires NO engine modifications and NO chemicals.
It is for these reasons that we offer a lifetime warranty and an unconditional 30 days Money-back guarantee.
Link to Hiclone fitting page
Save Fuel and More Power
Does your car use all the fuel you pay for? NO. Any fuel you don’t use is the money you wasted.
Do the Car Manufacturers Use Hiclone Fuelsaver swirl technology? 
They do, and have done so for years. On the left is the technology used by Mercedes Benz on their current model cars. On the right is our original Hiclone design.
Hiclone Fuelsaver has been on sale in Australia since 1989, and is the only fuel saving system to be copied by car manufacturers, the new generation of Direct Injection Petrol engines from companies like VW, Mazda etc, rely on Swirl Technology for their combustion process.
Hiclone Fuelsaver is a non-wearing part, which will never need replacement, or maintenance and it will not harm new car warranties; there is a law, which prevents vehicle manufacturers from doing so. We do supply new car dealers, who sell Hiclones to their new car customers.
In 1998 Nissan introduced the ZD30 3.0L TD engine with 2 swirl valves at the entrance of the inlet manifold.
In 2002 Toyota Europe had 6 swirl flaps installed on the local 1HD 4.2L TD engines in an additional spacer block between the inlet manifold and cylinder head. Since 2004 Toyota now have 8 swirl valves in the inlet manifold on the 1KD 3.0L TD engines.
In 2011 Audi, VW & Porsche have dramatically improved the economy of their new 3.0L V6 TDI by up to 1.5L/100km or 15%. In the inlet manifold there is now a single central swirl flap that swirls the air in the combustion chamber for efficient combustion, particularly at low engine speeds. The new single flap replaces the individual swirl flaps in the intake ports of the already efficient previous engine.
Mercedes V6 fitted with swirl technology has 18% more power than the previous engine. The economy has also improved from 12L/100km to under 10L/100km, a 2L/100km or 17% fuel saving (figures from Govt. tests printed in “Car” and “Wheels” magazines).
Subaru got 10% more economy and more power from their WRX in 2000 by fitting valves in their inlet runners to create a greater swirling of the intake charge in the combustion chamber (“Wheels” magazine).
Hiclones swirling effect makes fuel particles finer and allow up to 85% of the fuel to be burned, as opposed to about 60% in the best of conventional systems. This means you can travel further on the same amount of fuel. Hiclone supplies a more even mixture for every cylinder. This on LPG vehicles would help to protect the valves.
Hiclone maximizes the airflow and gathers fuel to the center of the air stream, then rapidly moves it to the combustion chamber preventing the adhering of particles to the wall of the intake system. Swirling fast-burn, near-complete combustion increases power output.
Hiclone has No moving parts and will therefore out last the life expectancy of any engine.
Hiclone requires NO engine modifications and NO chemicals.
It is for these reasons that we offer a lifetime warranty and an unconditional 30 days Money-back guarantee.
Link to Hiclone fitting page
What is your car?
Carburettor Engines
These engines generally have the highest fuel wastage, due to the distance the fuel has to travel prior to combustion. The Hiclone carries the fuel in the centre of the airflow, away from the sides of the manifold, to the combustion chamber.
We claim 15-20% fuel savings, but some old cars have achieved figures higher than 35% fuel savings.
Link to Hiclone fitting page
Diesel Engines
By increasing the swirl in the combustion chamber, to over three times the swirl the engine can ever naturally generate, Hiclone reduces the smoke from incomplete combustion by 50%.
Fuel savings on a new engine will be 5-10%, and on an older engine 10-20%. It is also common for customers to install extra Hiclones to non-turbo vehicles as well. On our “More Economy” page there is the “4X4 Australia” magazine test on a 4.2L Toyota diesel. They achieved 17% with one and 23.5% fuel savings with two Hiclones fitted. Link to Hiclone fitting page
Electronic Fuel Injected Engines (Petrol & Diesel)
By using sensors like Air Flow Meters on the inlet and O2 sensor on the exhaust, the engine's ECU will match the air/fuel ratio and create a new fuel map. The ECU will need time to re-learn (about a week) this is why dyno shops who test products by doing one run without, and one run with any product don't know how to use a dyno on an EFI car (as proven in the “Street Commodore” magazine test on our “More Power” page). You will use less fuel to achieve and maintained the same speed. A second Hiclone will give a further increase in airflow. Link to Hiclone fitting page
Turbo Engines
For Turbo vehicles we suggest installing Hiclones in two locations.
The first Hiclone is installed near the intake manifold; after the Turbo or intercooler; to improve combustion and economy.
The second part is installed near the air filter, before the Turbo. This part helps the Turbo Impellor to spin, reducing Turbo lag, bringing the boost in around 400-500rpm earlier.
It is also possible to install extra Hiclones in power or economy positions to further improve the vehicle. We have a lot of customers with up to 6 Hiclones installed on one vehicle. Link to Hiclone fitting page
LPG & CNG (Gas) Engines
The biggest problem for gas engines (incl Petrol and Diesel conv) is in standard form the gas mixture and airflow delivered to each cylinder is not even. This causes increased heat and wear on the engines, even the upper-cylinder lubricant has only reached a few of the cylinders. New gas systems now use multi-injectors to try and solve this problem. But even though they now deliver the same amount of gas to each cylinder, the poor design of the factory inlet manifold does not deliver the same amount of air to each cylinder, so the same problem still exists. Link to Hiclone fitting page
Hiclone was designed to deliver an even mixture and better airflow pattern to each cylinder. Which is why most people comment on how smooth and quiet the engine becomes after installing our product. Hiclone is the most effective gas mixer available and large gains have been achieved with Hiclone on these engines. Some people argue that gas and air mix naturally because they are both gases, but this is the same as saying that oil and water mix well because they are both liquids.
Vehicles optimised for gas only will save 5-10%, and up to 20% fuel savings for vehicles converted to gas (Dual Fuel). A 4.2L Carb engined Patrol achieved 17% fuel savings, and a BF Falcon with factory straight gas went from 15L/100km to 11L/100km. For older mechanical gas systems, the mixture must always be checked after installation, and it best to set the mixture to be slightly rich.
Link to Hiclone fitting page
Hiclone has No moving parts and will therefore out last the life expectancy of any engine.
Hiclone requires NO engine modifications and NO chemicals.
It is for these reasons that we offer a lifetime warranty and an unconditional 30 days Money-back guarantee.
When Does Hiclone Not Work?
Why does the same part work on one car and not work on another same model car? The reason is normally related to Air/Fuel ratio or engine tune. Hiclone increase's airflow at all times by up to 21%. The only time Hiclone can’t work is when there is a mechanical, electrical or fuel system problem. This means the engine is un-able to match the air/fuel ratio to the increase in airflow generated by the Hiclone product. If you add a lot of products to a car to increase airflow through the inlet or exhaust, at some point you will need to add more fuel to match (eg: in the UK if you fit a sports air filter to SU carbs you need to use richer needles). But this can be fixed. This is also why the first Hiclone usually saves more fuel than the second; it has access to the most un-burnt fuel. It is also why we offer the 30-day money back guarantee, so you have the choice to either have the problem fixed and save more money, or get your money back.
The rule is that any engine is only as efficient as the amount of fuel it can completely burn per combustion stroke and convert into power (torque), the more air per combustion stroke, with the correct air/fuel ratio, the bigger the bang and the right foot spends less time on the pedal. Ordering Hiclone for your car.
Beware! There are a few copies of Hiclone now!
The original invention is always the best because the people who designed it, researched and developed their product. These days any product can be copied, but a copy does not mean the copier understands what they are making. For example, many companies now make cyclonic vacuum cleaners, but only the original Dyson Vacuum cleaner does its job so well that it does not need any extra filters.
Beware! there are a few copies of Hiclone now, some even illegally using the Hiclone name. Most of them come as a flat strip of metal with the shape of the vanes cut into it. You very scientifically, bend them out with your fingers (the metal is very soft and flexible), you roll it into a circular shape, then push it in your air hose. All of these copies share one thing in common; all the vanes are only supported at one end. And with the pulsing of the airflow from the engines individual cylinders, causing the unsupported vanes to bend backwards and forwards. This causes metal fatigue at the bend, which is why in some early photos their parts have a sharp 90deg bend, and in later photos the bend is a greater radius. This radius did slightly increase the life expectancy, but metal fatigue still occurs. The end result is the vanes break off, bye-bye engine. You cannot make any claim against their company because they are not in Australia, and the people re-selling them here are not insured. This has happened already, and someone here tried to sue us for a product which was made by one of these companies.
There is even two products with spinning propellers, one is a computer fan, the other just a propeller on a bearing, with No lubrication available for the bearing the propellers either break off or reach a stall speed and then refuse to spin any faster and this then creates a restriction.
Hiclone has no moving parts, it is triangulated, engineered to last and never wears out. All Hiclones are hand assembled and individually inspected so that they are safe to fit in the entrance of an engine intake manifold. And we are in business since 1989. We offer a 30-day money back guarantee on Hiclone Fuelsaver .
Hiclone expert advice for fuel economy installation points
Hiclone Pty Ltd provide technical support services to our fitting stations, which are located in most areas of Australia.
If your vehicle is non-standard or on gas, our experienced staff will be able to find the correct solution for your vehicle. We have over twenty years experience working with the dynamics of airflow for engines increasing fuel economy.
The location for installing Hiclone Fuelsaver units to different vehicles is critical to the results you can achieve for your vehicle. The “Easy Installation Guide” may sound like installing a Hiclone Fuelsaver is child’s play; the reality is this guide will only work on a few vehicles and not most cases. When we choose the optimum locations to achieve the desired results, we also have to consider information like the bore to stroke relationship of the particular engine. Our official fitting stations always have access to this information. This will save you, our valued customers; time, money and inconvenience.
Link to Hiclone fitting page
Hiclone has No moving parts and will therefore out last the life expectancy of any engine.
Hiclone requires NO engine modifications and NO chemicals.
It is for these reasons that we offer a lifetime warranty and an unconditional 30 days Money-back guarantee.